ECO EMULSION EE - 4010

ECO EMULSION Acrylic Emulsion Paint EE – 4010 is a decorative paint for interior made from acrylic emulsion and special color pigment. This product is designed for interior wall and ceiling surfaces including brick work, cement plaster, concrete, gypsum, GRC panel, wood, plywood, etc. ECO EMULSION Acrylic Emulsion Paint EE - 4010 has good adhesion to substrates, easy to apply, fast drying, good hiding power, bright color and available in many beautiful colors.


Features & Benefit :
  • Good adhesion to the substrate
  • Good hiding power
  • Easy to apply and fast drying
  • No added lead or mercury

Packaging : 5 Kg & 25 kg.

Color Card

 * 
 


5 stars - based on 415 reviews
APPLICATION PROCEDURE

A. Application Procedure for Wall Surfaces

Prepare the surfaces
Surfaces must be dry, clean and free from all contaminants. Newly build wall must be dry after 28 days old.
Area of defect, like crack or existence of puncture, repair using materials mixture of PROCRETE Cement Filler CF – 700 with PROCRETE Bonding Agent BDA – 810 and water.
Make sure moisture content / dampness of wall ? 16% measured using Protimeter appliance and wall alkalinity (pH) 7 – 8 measured using Universal pH indicator.

Primer coat
DECOR Alkali Resisting Primer AR – 300 (Water Based), 1 coat (1 x 20 microns without thinning); or use DECOR Alkali Resisting Primer AS – 310 (Solvent Based) 1 coat (1 x 20 microns without thinning) for concrete wall with higher alkalinity.   

Repair
After primer coat has dried, check all surface paint whether there are defects like crack or existence of puncture. If there is part of wall defect, repair using materials mixture of PROCRETE Cement Filler CF – 700 with PROCRETE Bonding Agent BDA – 810 and water. Afterwards apply primer coat once again at parts of repaired, then let it run dry minimal 2 hours.

Finish coat
ECO EMULSION, 2 coats (2 x 30 microns, dilute with 10 – 20 % clean water according to application need).


B. Application Procedure for Gypsum Surfaces
Painting gypsum surfaces
  1. Cleaning the surface of gypsum from all contaminants like : dirt, grease, oil and ascertain surface of gypsum and gypsum extension have closed perfection and flatten and also dry.
  2. Area of defect, repair using DECOR Wall Filler DWF – 200 and allow to dry ± 24 hours or depend on its thickness.
  3. Apply primer coat DECOR Wall Sealer DWS – 320 (Water Based), 1 coat (1 x 15 microns, without thinning).
  4. After primer coat has dried, check all surface paint whether there are defects. If there is part of wall defect, repair using DECOR Wall Filler DWF – 200 and allow to dry ± 24 hours or depend on its thickness. Afterwards apply primer coat once again at parts of repaired, then let it run dry minimal 2 hours.
  5. Apply top coat : Eco Emulsion Acrylic Emulsion Paint, 2 coats (2 x 30 microns, dilute with 10-20% clean water according to application need).

TECHNICAL DATA


Type Acrylic Emulsion
Color 24 standard color (as shown in the color card)
Specific Gravity 1,50
Solid by Volume 37%
Theoritical coverage 8,2 m?2;/kg (1 layer)
Recommended dry film thickness 2 layers, 60 microns (2 x 30 microns)
Application methods brush, roll, airspray or airless spray
Diluent clean water
Thinning ratio ± 10%
Drying Time depend on temperature and humadity
surfacedry: 60 minutes (30°C)
Recoating Interval Minimum 2 hours (30°C)