NEW PAINTING
1. Surface Preparation
- All wall surfaces with defects such as hairline cracks or small holes, repaired using PROCRETE Cement Filler CF – 700 mixed with PROCRETE Bonding Agent BDA – 810 and water, then let it dry for at least 5 (five) days.
- Make sure the water content / humidity of the wall? 16% is measured using a Protimeter tool and the wall alkali content (pH) 7 – 8 is measured using a Universal pH indicator tool.
- The wall surface must be cleaned of dirt, dust, grease, oil, remaining cement water and others .
2. Base Coat
- Apply 1 (one) coat of ECO EMULSION Alkali Resisting Primer EAR – 4001 (Water based) without dilution or use DECOR Alkali Resisting Primer AS – 310 (Solvent Based) without dilution using a roll for wall surfaces with very high alkaline levels. Allow this base coat to dry for at least 2 (two) hours.
3. Touch Up
- Check the entire surface of the wall that has been primed again, if defects such as hairline cracks or small holes are found, do local repairs using ECO EMULSION PLAMUR Ready to Use Wall Putty ECP – 4030 using a cloth application tool, then let dry ± 2 – 24 hours, depending on thickness. dry for at least 2 (two) hours.
4. Final Coat
- Apply 1 (one) layer of finish paint ECO EMULSION Acrylic Emulsion Paint EE – 4010, which is diluted with clean water 10 – 20 ?rat, using a roll . Then let this first coat of finish paint dry for at least 2 (two) hours
- Do it again until the third layer (if the color of the second layer has not completely covered)
REPAINTING (OLD PAINT HAS BEEN BROKEN & PEELED)
1. Surface Preparation
Check the condition of the old paint that is still attached to the wall, if the old paint is damaged or calcified or peeling, then do the following steps:
- Peel off all the old paint using PROPAN Paint Remover PPR – 735 (blue can) until it reaches the wall plaster, then clean it and let it dry.
- All damaged wall surfaces are repaired using PROCRETE Cement material Filler CF – 700 mixed with PROCRETE Bonding Agent BDA – 810 and water, then let it dry completely for at least 5 (five) days.
- Make sure the moisture content / humidity of the wall? 16% is measured using a Protimeter tool and the wall alkali content (pH) 7 – 8 is measured using a Universal pH indicator tool.
- The wall surface must be cleaned of dirt, dust, grease, oil, remaining cement water and others .
2. Base Coat
- Apply 1 (one) coat of ECO EMULSION Alkali Resisting Primer EAR – 4001 (Water based) without dilution or use DECOR Alkali Resisting Primer AS- 310 (Solvent Based) without dilution using a roll for wall surfaces with very high alkaline levels. Allow this base coat to dry for at least 2 (two) hours
3. Touch up
- Check the entire surface of the wall that has been primed again, if defects such as hairline cracks or small holes are found, do local repairs using ECO EMULSION PLAMUR Ready to Use Wall Putty ECP – 4030 using a cloth application tool, then let dry ± 2 – 24 hours or depending on thickness. dry for at least 2 (two) hours
4. Final Coat
- Apply 1 (one) layer of finish paint ECO EMULSION Acrylic Emulsion Paint EE – 4010, which is diluted with clean water 10 – 20 ?rat, using a roll . Then let this first coat of finish paint dry for at least 2 (two) hours
- Do it again until the third layer (if the color of the second layer has not completely covered)
REPAINTING (OLD PAINT STILL IN GOOD CONDITION & NOT PEELED)
1. Surface Preparation
If the condition of the old paint is still good, nothing is peeling off, then do the following steps:
- Clean the entire surface old paint from dust and dirt that sticks to it by washing it with a brush & clean water or a damp cloth, then let it dry, or sand it using sandpaper size 180, then clean it from dust.
- Make sure the water content / moisture content of the wall is below 16% measured using the Protimeter tool and the wall alkali content (pH) 7 – 8 measured using a tool Universal pH indicator.
2. Base Coat
- Apply 1 (one) coat of base coat DECOR Wall Sealer DWS – 380 (solvent based) or DECOR Wall Sealer DWS – 320 (water based) without dilution using a roll. Allow this base coat to dry for a minimum of 2 (two) hours and a maximum of 4 (four) hours.
3. Final Coat
- Apply 1 (one) layer of finish paint ECO EMULSION Acrylic Emulsion Paint EE – 4010, which is diluted with 10 – 20% clean water, using a roll. Then let the first coat of finish paint dry for at least 2 (two) hours
- Do it again until the third layer (if the color of the second layer has not completely covered)
