Decor Acrylic Enamel 560

NEW PAINTING
 1. Surface Preparation 

• All wall surface defects such as hairline cracks or small holes, repaired using PROCRETE material Cement Filler CF – 700 mixed with PROCRETE Bonding Agent BDA – 810 and water, then let it dry for at least 5 (five) days.
• Make sure the moisture content / humidity of the wall is under 16% measured using a Protimeter and alkali content wall (pH) 7 – 8 measured using a Universal pH indicator tool.
•  The wall surface must be cleaned of dirt, dust, grease, oil, remaining cement water and others.

 2. Base Coat 

•  Apply 1 (one) layer of DECOR Alkali Resisting Primer AS – 310 (Solvent Based ) without dilution using a roll. Allow this base coat to dry for at least 2 (two) hours

 3. Touch Up 

•  Check the entire surface of the wall that has been primed again, if found there are still defects such as hairline cracks or small holes, do local repairs using PROCRETE Cement Filler CF – 700 mixed with PROCRETE Bonding Agent BDA – 810 and water, then let it dry for at least 5 (five) days
•  Reapply base coat, especially on the repaired parts, then let it dry for at least 2 (two) hours

 4 . Final Coat 

•  Apply 1 (one) coat of finish paint DECOR Acrylic Enamel DAE – 560 (Water Based) , which is diluted with clean water 10 – 20% by volume, using a roll. Then let this first coat of finish paint dry for at least 2 (two) hours. REPAINTING (OLD PAINT HAS BEEN BROKEN & PEELED)
   1. Surface Preparation 
  Check the condition of the old paint that is still attached to the wall, if the old paint is damaged or calcified or peeling, then do the following steps – following steps :
  •  Peel off all the old paint using PROPAN Paint Remover PPR – 735 (blue can) until it reaches the wall plaster, then clean and let dry.
  •  All surfaces the damaged wall is repaired using PROCRETE Cement Filler CF – 700 mixed with PROCRETE Bonding Agent BDA – 810 and water, then let it dry completely for at least 5 (five) days.
  • Make sure the moisture content / humidity of the wall under 16% is measured using a Protimeter tool and the wall alkali content (pH) 7 – 8 is measured using a Universal pH indicator tool.
  •  The wall surface must be cleaned of dirt, dust, grease, oil, remaining cement water and others .

   2. Base Coat 

  •  Apply 1 (one) layer of DECOR Alkali Resisting Primer AS – 310 (Solvent Based ) without dilution using a roll. Let this layer of base paint dry for at least 2 (two) hours.

  3. Touch up 

  •  Check the entire surface of the wall that has been primed again, if found there are still defects such as hairline cracks or small holes, do local repairs using PROCRETE Cement Filler CF – 700 mixed with PROCRETE Bonding Agent BDA – 810 and water, then let it dry for at least 5 (five) days
  •  Reapply base paint, especially on the repaired parts, then let it dry for at least 2 (two) hours.

  4. Final Coat 

  •  Apply 1 (one) coat of finish paint DECOR Acrylic Enamel DAE – 560 (Water Based) , which is diluted with clean water 10 – 20% by volume, using a roll. Then let the first finish coat of paint dry for at least 2 (two) hours. /p>

    REPAINTING (OLD PAINT STILL IN GOOD CONDITION & NOT PEELED)
     1. Surface Preparation 
    If the condition of the old paint is still good, nothing is peeling off, then do the following steps:

    • Clean the entire surface of the old paint from dust and adhering dirt by washing it with a brush & clean water or a damp cloth, then let it dry, or sand it using sandpaper size 180, then clean it from dust.
    • Make sure the water content / humidity of the walls under 16% was measured using a Protimeter tool and the wall alkali content (pH) 7 – 8 was measured using a Universal pH indicator tool

    2. Base Coat 

    •  Apply 1 (one) coat of DECOR Alkali Resisting Primer AS – 310 SB or DECOR Wall Sealer DWS – 380 SB without dilution using a roll. Allow this base coat to dry for a minimum of 2 (two) hours and a maximum of 4 (four) hours.

    3  . Final Coat 

    •  Apply 1 (one) coat of finish paint DECOR Acrylic Enamel DAE – 560 (Water Based) , which is diluted with clean water 10 – 20% by volume, using a roll. Then let this first coat of finish paint dry for at least 2 (two) hours.